LI12390 Features: -Can be driven with a 1/2" breaker bar from the end, create your own handle. -Neck design fits many oxygen sensors with heat shields. -Forged and heat-treated for superior strength. -Six point design helps prevent slipping like 12 point toolsUse with a breaker bar to loosen stubborn oxygen sensors. Tool comes with both 1/2" and 3/8" drive. Attach a 1/2" breaker bar on the end of the tool to initially loosen stuck sensors. Use a 3/8" ratchet on the top for fast removal and installation. Fits oxygen sensor applications with a heat shield. Slotted body allows clearance for wire harnesses. Forged, heat-treated steel with six point design will withstand high torque removal applications.. Generic Dimensions: -Also has standard 3/8" drive on top of tool for use with a ratchet. Dimensions: Overall Height - Top to Bottom: -1.75 Inches. Overall Width - Side to Side: -3.5 Inches. Overall Product Weight: -0.56 Pounds.
Vibrant Heat Sleeving - 0 - 0 UNIVERSAL NON APPLICATION SPECIFIC ALL ALL ALL ; - 25811 Vibrant Heat Sleeving is offered in a number of variations to meet your exact requirements. * Flexible Split Sleeving * Heat Protect Flexible Sleeving * ExtremeShield 1200 Flexible Tubing * ExtremeShield 1400 Flexible Tubing
Yeeco Color Recognition/Discrimination Module Color Sensor with a Wide-angle Lens
1, on-board the color sensor
2, with [wide-angle lens], removable, you can identify a large area or small area of objects.
3, support 3V-5V voltage input
4, the pin of the chip all have to bring out the pins as the standard 100mil (2.54mm), easily used for the dot matrix board
5, with four-bright white LED can illuminate some of its non-luminous objects. LED controlled.
6, S1 S2 S3 S4 can be on-board pull-up or drop-down.
7, two 3mm mounting screw holes, spacing 16.5mm
8,PCB size: 23mm X 30mm
WE DO NOT provide specific technical
1x color module
Put a slot in the side of this wrench to accommodate connectors on heated oxygen sensors, which usually won't fit in standard sensors wrenches.
The extended and reinforced body removes the most stubborn sensors without rounding them off.
Features 1/2 of the double square drive, 7/8" (22mm) hex.
Flare nut for vacuum switch & oxygen sensor service on the computer-controlled engines.
FORD, TOYOTA, NISSAN, BENZ, BMW and most of the euro cars.
7/8" (22mm) heated oxygen sensor socket:
Slot in socket accommodates the connectors on heat oxygen sensors and has a double 1/2" drive for easy access.
7/8" (22mm) Low Profile Offset Oxygen Sensor Short Socket:
Designed for use in tight spaces. For use with a 3/8" drive tool.
7/8" (22mm) Oxygen Sensor Long Socket:
Removes and installs oxygen sensors in most domestic and some imported vehicles. Socket is slotted to allow for wire clearance. For use with a 3/8" drive tool or turn with a 1" wrench.
7/8" Universal Vacuum PVS, TVS Valve and Oxygen Sensor Socket:
Removes and installs vacuum switches with a 7/8" hex. Also fits some oxygen sensors. For use with a 3/8" drive tool or turn with a 1" wrench.
1" and 1-1/16" Oil Pressure Sending Unit / Vacuum Switch Socket:
Socket has a 1" and 1-1/6" hex to remove oil pressure sending units. Use with a 3/8" drive tool or turn with a 1-1/8" wrench. Deep design fits switches up to 2-5/8".
1-1/16" (27mm) GM Thermal Sensor Switch Socket:
Removes and installs 1973 thru 1977 GM thermal sensor switch and fits some oil pressure sending units. For use with a 1/2" drive tool.
1-3/16" (29mm) Oil Pressure Sending Unit / Vacuum Switch Socket:
Fits 1-3/16" oil pressure sending units found on late 80's and mid 90's GM vehicles. For use with a 1/2" drive tool.
For Becker, Porsche, Mercedes Benz, VW (NO. 3 x 2PCS)
BMW Opel L Wrench Becker (New) and Skoda (new), Blaupunktx 2 pcs, addition 2 pcs JVC poineer
Special socket for removing oxygen Sensor.Including:1/2 inch Dr. x29mm x 90mL (7mm s lot);1/2 inch Dr. x27mm(12pt) x 82mL; 3/8 inch Dr.x7/8"x 90mL (20mm slot); 3/8 inch Dr. x1-1/16" x74mmL;1/2 inch Dr. x22mm x 50mL; 3/8 inch Dr. x22mm x 31mmL