Yontree Torque Multiplier Set Wrench Lug Nut Lugnuts Remover Labor Saving Heavy Duty
Specifications: Material: High-quality Alloy steel Trans-Speed ratio: 1:58 Maximum safe output: 4800 N/M Rocking bar length: 10.6", weight: 428 g Net weight: 16 lbs. Features: Suitable for Trucks, Buses, RVs and Other Heavy Duty Vehicles Labor saving wrench: made from extra sturdy alloy steel to withstand daily wear Four free sockets for deep wheel wells 3.93" long rocking bar is wrapped with rubber foam for better hang grip Storage Type: Black Blow-molded case 90-day manufacturer's warranty Package includes: (3) 6-point sockets: 41 mm (1-5/8"), 38 mm (1-1/2"), 33 mm (1-5/16") (1) 4-point/square (for square duel lug studs) socket: 21 mm (13/16") (1) 75 mm tall Long bar (1) Storage Case (1) Wrench (1) Rocking bar (1) Long bar
RamPro Â¼â€ Drive Click Torque Wrench Low Range (20-200 in.-lbs./23-230 CM-KGs) | Micrometer Adjustable Dual-Direction Ratcheting Bar with Click Stop Twist SAE/Metric Dial Gauge | Great for Cars/Bikes
About The Ram-Pro CR-V 1-4 inch Drive Click Stop Ratchet Torque WrenchEver needed to tighten a set of bolts/nuts to a desired & recommended Torque, as when fixing vehicle engines or Repairing Bikes/Firearms, Precision is of course key to getting the job done right.Introducing:The Ram-Pro Reversible 1/4 in. Square Drive Click Type Micrometer Adjustable Torque Wrench, which is the go-to tool when precise leverage torque is needed.TQ with Confidence:Wrench is pre calibrated to +/-4% accuracy for assured precisionYou Get:Â¼" Torque WrenchBlack Storage CaseUser's Manual with Conversion TableSocket Holder:Spring-loaded detent ball securely latches onto sockets, preventing Fall-Offs.Setting Torque:Turn Knurled Handle with Horizontal Engraved Micro Graduations.Also dial-able with a Hex Wrench for easier presetting.Dual Torque Range Scale:20-200 Inch Pound23-230 CM.KGS/KPS (2.26-22.6 Newton Meters)Increment Increase:1 in-lb..53 KGS-CMConversion Table:1 ft-lb=0.1383MKg=1.3556Nm1 MKg=7.233ft-lb=9.806Nm1 Nm=0.1019MKg=0.73756ft-lb(Complete Conversion Chart included).Loud Tangible Micro-Clicker:When Preset TQ is reached an Automatic Wrench Click Sound is Heard & Felt (for noisy environments), Do not pull further or you risk damaging the studs.Dual-Direction:Torque is measured Clockwise & Counterclockwise to tighten & loosen cap heads.Black Storage Case:Blow Molded Plastic Case is included for tool security, easy transport & efficient storage.Tip:When Storing the Wrench, Dial it down to the lowest torque setting (don't turn handle below lowest torque setting).Excellent Tool for doing Auto Engine Work.DIY Gauge Tool for your Bike Repair.Make a Safer World Through Accuracy & Precision!
Fix It Sticks FISTL65 65 Inch Lb Miniature Torque Limiter
Manufacturer: Fix It Sticks
Brand: Fix It Sticks
For shooters and hunters, adjustments in the field are sometimes necessary to keep equipment in prime working order. Unfortunately, this oftentimes requires odd or uncommon bit sizes and bulky tools. Building on the perfect portability and modularity of its tools for cyclists, Fix It Sticks introduces its Torque Limiter line to meet the specialized requirements of shooters and hunters. Use the Fix It Sticks Torque Limiter any time limiting over-tightening of fasteners is needed.
Control Devices Brass Continuous Run Unloader Valve
Manufacturer: Control Devices
Brand: Control Devices
The LGM 30 - Mark III continues the tradition of the original Mark II. 25 years of experience were incorporated into the design and development of this continuous run control. The Mark III combines all components required for a continuous run compressor application: the pilot valve, the vent valve, and the check valve. Since the Mark III is a "vent" unloader, built-in compressor head unloaders are not required. The compact size and straight-through flow design of the Mark III make installation easy. Simply install the Mark III into the air receiver, and attach the compressor discharge line to the valve inlet. The Mark III is suitable for compressors of up to 30 SCFM delivery. Cut-in and cut-out pressure settings are factory set to customer specifications. Minimum cut-out pressure is 250 PSI. If no setting is specified, the valve is set at our standard setting of 115 PSI cut-out and 95 PSI cut-in. The valve is also field adjustable. Details of construction include a forged brass body, zinc-plated steel internal components, fluorocarbon piston ring, stainless steel springs, and a glass-filled fluropolymer check valve poppet. Options include a 1/8" NPT tapped port for throttle control of a gas engine, a lockout clip for "dual control" applications, a special 1/8" NPT tapped port for pressure switch unloader valve, a vent port muffler, and a toggle unloading lever for one-hand warm up control. Vibra-Seal pre-applied thread sealant is also available on external inlet pipe threads.
Tenive Torque Multiplier Wrench Set is great for loosen and removes lug nuts from vehicle which includes convenient carrying case, handle and wrench accessory. Most are too small to handle trailer wheels and only work on steering wheels, they are also much smaller and weaker that is why you won't find any with a lifetime warranty. Specification: Max torque: 320 N.M Gear ratio: 1:16 Material: High-quality Steel Package including 1xWrench3xSocket: 17mm, 19mm, 21mm1xStorage carrying case
When precision is your top priority, you can depend on the superior performance of Crescent micrometer torque wrenches. The new Crescent micrometer torque wrenches offer a dependable, fast, and accurate way to tighten fasteners in automotive, agricultural, and commercial/industrial applications. Reversible ratcheting heads make work easier in tight spaces and an audible signal lets you know your target torque has been reached. A slide-back adjustment collar design and large laser-etched markings make setting target torque simple and Quick.
Wiha 28502 TorqueVario-S Torque Screwdriver, 5-10 Inch Pound
All models have an integrated direct reading window scale that eliminates false readings by displaying the torque value. The torque value is continuously adjustable by using the provided adjustment tool (torque setter) which prevents unauthorized torque changes. Tested in accordance with EN ISO 6798, BS EN 26789, ASME B107.14M. Ergonomic multi-component handles, light and compact, Size proportional to optimize torque range. Audible click when torque setting is reached. Includes Certificate. With Window Scale Pre-Sets In. lbs: 5-10
Brand: Total Implant
Dental Implant Torque Wrench Adapter For Straumann Type Implant Torque Wrench. This item fits to straumann torque wrench. Inner 4mm Square fit to Nobel Biocare Drivers. If you own Straumann wrench, you can use Nobel biocare drivers, expanders, or other tools.